|
ARCADEVGA 5000 D9800 1024?
#335522 - 12/29/14 03:26 PM
|
|
|
I have the arcadevga 5000 and a wells gardner d9800 running windows 7 64 and I had the desktop running 1024x768 and it looked fine. something happened and now if I run that resolution the screen is bowed in the center on the sides and wont adjust out. I have tried to uninstall the drivers and start over but after it uninstalls the screen goes blank so I cant see anything and after a restart it wont install the driver I get a blank screen and have to use system restore. I want 1024 because if I am doing any setting changes the bottom is cut off where you click apply, save close thanks
|
|
|
|
Re: ARCADEVGA 5000 D9800 1024?
[Re: erik]
#335534 - 12/30/14 06:07 AM
|
|
|
Use the shortcut keys on the keyboard. They're underlined in the boxes. I had the same problem and you can't drag the window bar high enough to click. It'll still work though. And in case it doesn't work, remember the keys to discard changes to revert. I think/hope that's what you mean... GL
|
Pessimist: Oh, this can't get any worse!
Optimist: Yes, it can!
|
|
|
Re: ARCADEVGA 5000 D9800 1024?
[Re: Bad A Billy]
#335543 - 12/30/14 01:36 PM
|
|
|
thanks, but I had this at a higher res. something got messed up with the driver but the key shortcuts helped
|
|
|
|
Re: ARCADEVGA 5000 D9800 1024?
[Re: erik]
#335560 - 12/31/14 06:24 AM
|
|
|
|
|
The D9800 won't do 1024x768.....
[Re: krick]
#335595 - 01/01/15 04:18 AM
|
|
|
That's out of spec. I'm surprised you're getting anything at all.
|
Scifi frauds. SF illuminates.
_________________
Culture General Contact Unit (Eccentric)
|
|
|
Re: The D9800 won't do 1024x768.....
[Re: Traso]
#335600 - 01/01/15 07:18 AM
|
|
|
|
|
Re: The D9800 won't do 1024x768.....
[Re: krick]
#335866 - 01/08/15 10:50 PM
|
|
|
i got 1024x768 lokking ok again by right clicking on the desktop and selecting in windows that resolution. after that now using the little galaga icon and switching from 800 to 1024 now works fine?
|
|
|
|
Re: The D9800 won't do 1024x768.....
[Re: erik]
#335895 - 01/10/15 05:47 AM
|
|
|
> i got 1024x768 lokking ok again by right clicking on the desktop and selecting in windows that resolution. after that now using the little galaga icon and switching from 800 to 1024 now works fine?
I dunno. That monitor is a digital multisync. I swear when I had one, and one reason I didn't keep it, was that its max res was 800x600. Also, as I recall, it's the flat tube version of the D9400, and its manual says the scan rate is 15-50khz. It's continuous, too. Oh well. What bit depth did you select, 16 or 32?
|
Scifi frauds. SF illuminates.
_________________
Culture General Contact Unit (Eccentric)
|
|
|
Re: The D9800 won't do 1024x768.....
[Re: Traso]
#335941 - 01/11/15 06:28 PM
|
|
|
|